MANUAL DE INSTALACIÓN

ADHESIVO PEGAFAST

1. SELECCIÓN DEL ADHESIVO PEGAFAST
Seleccion del adhesivo Pegafast
Antes de comenzar con la aplicación, se debe comprobar que el adhesivo a utilizar es el adecuado para el tipo de sustrato y la clase de trabajo que se va a realizar.
2. PREPARACIÓN DE LA SUPERFICIE
Preparacion de la superficie
Compruebe que el sustrato esté libre de polvo, grasas, pintura, etcétera.
Verifque que el sustrato tenga una planeidad (menor de 3 mm) y porosidad adecuada.
El sustrato no debe presentar humedad (inferior al 3%).
3. PREPARACIÓN DEL ADHESIVO PEGAFAST
Preparacion del adhesivo Pegafast
Agregue siempre el mortero al agua y no al revés. Utilice 6.4 litros de agua por bulto de 25 kg.
Mezcle hasta obtener una consistencia pastosa y homogénea. Posteriormente extienda el mortero con la parte dentada de la llana inclinándola a 45°.
Deje reposar por 5 minutos y vuelva a mezclar.
4. APLICACIÓN DEL ADHESIVO PEGAFAST
4-aplicacion-del-adhesivo-pegafast
Extienda una capa delgada del adhesivo sobre la tableta haciendo presión con la parte lisa de la llana.
Posteriormente extienda el mortero con la parte dentada de la llana inclinándola a 45°.
Aplique solamente la cantidad que puede cubrir en 15 minutos.
5. IMPORTANTE
Importante
Para formatos superiores a 30 x 30 cms de baja absorción y/o en exteriores es necesario frisar siempre la tableta en la cara posterior con la parte lisa de la llana dentada.
6. INSTALACIÓN
Instalacion
Coloque las tabletas, moviéndolas y realizando golpes suaves con un martillo de caucho hasta conseguir el total aplastamiento de los surcos generados por la llana dentada y una correcta adherencia de toda su superficie.
Respete las juntas de construcción.
Retire residuos y limpie.
Espere 24 horas para el proceso de emboquillado.

<--- Continua con PEGAFAST BOQUILLA ...

Indoor porcelain

ADHESIVE FOR COATINGS

PERFORMANCE

Format (cm) Flat (mm) Performance (Kg/m²)
30 x 30 6 x 6 4,5
40 x 40 6 x 6 / 6 x 10 5,0
50 x 50 10 x 10 6,0
60 x 60 10 x 10 / 12 x 12 7,0
80 x 80 12 x 12 / 10 x 15 10,0
60 x 120 15 x 15 9,0
100 x 100 15 x 15 12,0

IMPORTANT

Our technical advice whether verbal, in writing or through tests is practiced according to our knowledge, but should be considered only as an indication WITHOUT LIABILITY. As we DON’T KNOW or are able to intervene in the execution of the work, this information represents general indications that do not compromise MSC in any way.

The data sheet may not reflect all applications and factors involved in the use of the product. Thus, for non-descriptions on this file, we recommend a consultation with our technical department or carry out a test to check their suitability.
MSC guarantees that its products have been checked for their quality laboratory and are in accordance with the characteristics described in the technical specifications.

Pegafast │ Indoor Porcelain

It is a gray and white cement dry based mortar, modified with cellulosic additives latex type. It has excellent working properties and unmatched adhesion of porcelain tile for floors and interior walls.

Benefits

  • High indoor adhesion.
  • Zero slip.
  • Excellent consistency of work.
  • Long open time.
  • Higher performance given its special grain size.

Suggested use

  • Cement based plastering.
  • Concrete.
  • Block.
  • Masonry in general.

Presentation

  • Plastic bags of 10 kg (22 lbs), 25 kg (55 lbs) y 40 kg (88 lbs).

Colors

Gray and white

Preparation

Preparation of the surface or support
All surfaces and the environment must be between 5°C (41°F) and 35°C (95°F). Verify that the surface is structurally sound and strong, completely set free from active cracks or loose parts, dust, grease and oil residues, stucco, paint, grout, concrete sealers, curing agents potentially harmful to adherence of the glue. If the surface is very absorbent or dry, pre-wet.

Application

Preparation and Application of the Product
Always add the mortar to water and not vice versa. Use 6 liters of water per package of 25 kg (55 lbs). Mix until the consistency is homogeneous. Let stand for 5 minutes, then mix. Extend only the area that you can install in 15 minutes maximum. Always use a notched trowel appropriate to the tablet format being installed. Add mortar with the flat side of the trowel on the back of the tablet and then install, hit softly with a rubber hammer.